Programming Instructions for 2010 Buick Allure:
Please Note: This vehicle requires the Vehicle Remote to be programmed by a qualified professional.This requires that a Locksmith use specialized computer equipment to program your vehicle remote.
Helpful Instructions:
OR
Locksmith Search
Key Programming Information for 2010 Buick Allure
FOR VEHICLES WITH REGULAR IGNITION (North America, except Canada):This procedure requires that a programmed working key is available for the vehicle. This procedure adds keys only. The procedure does not erase previously learned keys. The new key to be programmed needs to be cut prior to performing this programming procedure.
1. Insert the original, already programmed key in the ignition and start the engine.
2. After the engine has started, turn the key off and remove the key.
3. Insert the key to be programmed and turn it to on within 10 seconds of removing the original key (do not start the engine).
4. The security light will turn off once the key has been programmed. It may not be apparent if the security light went on due to how quickly the key is programmed. If your vehicle does not have a security light wait 10 minutes and 45 seconds to make sure the key has been programmed.
5. Repeat steps 1 through 5 if additional keys are to be programmed.
FOR VEHICLES WITH PUSH BUTTON IGNITION (North America, except Canada):
PROGRAMMING INSTRUCTIONS IF YOU HAVE AT LEAST ONE WORKING TRANSMITTER (PROXIMITY KEY) ALREADY:
A new transmitter can be programmed to the vehicle when there is one recognized transmitter. To program, the vehicle must be off and all of the transmitters, both currently recognized and new, must be with you. The key blade needs to be cut prior to performing this programming procedure.
1. Place the recognized (already programmed) transmitter in the cupholder.
2. Insert the new key into the lock cylinder located on the outside of the driver door and turn the key to the unlock position five times within ten seconds. The Driver
information Center (DlC) should display Ready For Remote #2,3,4 or 5.
3. Place the new transmitter into the transmitter pocket. The transmitter pocket is located inside
the center console storage area under the cupholder. The cupholder will need to be pulled out
to access the transmitter pocket.
4. Press the ignition. When the transmitter is learned, the DIC display will show that it is ready to
program the next transmitter.
5. Remove the transmitter from the transmitter pocket and press the unlock button.
To program additional transmitters, repeat Steps 3 through 5, When all additional transmitters are programmed, press and hold the ignition for 5 seconds to exit the programming mode.
PROGRAMMING INSTRUCTIONS IF YOU DON'T HAVE ANY WORKING TRANSMITTERS:
lf there are no currently recognized transmitters available, follow this procedure to program up to five transmitters. This procedure will take approximately 30 minutes to complete. The vehicle must be off and all of the transmitters you wish to program must be with you. The key blade needs to be cut prior to performing this programming procedure. It is recommended that the vehicle be connected to a power source via jumper cables during this procedure as the vehicle's battery voltage will drop during the procedure.
1. Insert the new key into the key lock cylinder located on the outside of the driver door and turn the key to the unlock position five times within ten seconds. The Driver lnformation Center (DlC) displays Remote Learn Pending, Please Wait.
2. Wait for ten minutes until the DIC displays Press Engine Start Button To Learn and then press the ignition. The DIC displays will again show Remote Learn Pending, Please Wait.
3. Repeat Step 2 two additional times. After the third time, all previously known transmitters will
no longer work with the vehicle. The remaining transmitters can be relearned during the next
steps. The DIC should now show Ready For Remote #1.
4. Place the new transmitter into the transmitter pocket. The transmitter pocket is located inside the center console storage area under the cupholder. The cupholder will need to be pulled out
to access the transmitter pocket.
5. Press the ignition. When the ignition is learned, the DIC display will show that it is ready to program the next transmitter.
6. Remove the transmitter from the transmitter pocket and press the unlock button.
To program additional transmitters, repeat Steps 4 through 6. When all additional transmitters are
programmed, press and hold the ignition for 5 seconds to exit the programming mode.
Please Note:
Each vehicle can have up to five transmitters programmed to it.