How to Program a 2018 Mitsubishi Eclipse Cross Key Fob, Keyless Entry Remote, Smart Key
Programming Instructions Step by Step:Use these instructions if you have Remote Head Key System.To add a key, you must already have two programmed keys. You can have a total of 8 keys programmed.
1. Insert the first valid key into the ignition switch and turn the key to the ON position for 5 seconds.
2. Turn the key to the OFF position and remove the first key.
3. Within 30 seconds of removing the first key, insert the second valid key into the ignition and turn it to the ON position. Approximately 10 seconds later, the immobilizer display will start to blink.
4. When the immobilizer display starts blinking, turn the second valid key to the OFF position and remove it. Within 30 seconds after doing so, insert a blank immobilizer key into the ignition switch and turn it to the ON position. Perform this operation no more than 30 seconds after the immobilizer display starts blinking. When programming is complete, the immobilizer display will come on for 30 seconds then go off. If an error occurs, the blinking immobilizer display will go off during the procedure.
5. If you wish to register another key, perform the process again from step1.To program the remote portion of your key use these instructionsYou can program the remote portion to the system if you have one valid (already programmed) key by doing the following:1. Have available all (current and new) keys you wish to register2. With a valid (already registered) key, press the UNLOCK button (2) for 4 to 10 seconds. Then press and hold the LOCK button.3. Within 10 seconds of pressing the LOCK button, release the LOCK and UNLOCK buttons in sequence. At this time, programming for ALL KEYS THAT ARE PROGRAMMED except for the key used in steps 2 and 3 ARE ERASED and the answerback function (door is locked and unlocked) informs you that the registration mode has been activated.4. Within 60 seconds after step 3, complete the following ID code registration operation using the next key you wish to register within 4 seconds.) Press both the LOCK and UNLOCK buttons for 2 seconds.) Release both the LOCK and UNLOCK buttons for 1 second.) Press the UNLOCK button. The answerback function informs you that the ID code registration of the key is completed.5. To register the ID codes of additional keys, repeat step 4 within 60 seconds after step4.6. If no ID code of a key is registered within 60 seconds after step 4, the registration mode is canceled and the normal mode returns.
Use these instructions if you have the Fast Key Smart Key System.You can program new F.A.S.T.-keys to the system if you have two valid (already programmed) F.A.S.T.-keys and a blank (not programmed) F.A.S.T.-key. For F.A.S.T.-key programming, follow the procedures below.1. Open the driver's door.NOTE: Keep the driver's door open until F.A.S.T.- key programming is finished. Do not open or close other doors.2. While carrying the first valid F.A.S.T.- key, put the operation mode in ON. (Perform the following procedure within 30 seconds.)3. With the first valid F.A.S.T.-key, press the UNLOCK button for 4 to 10 seconds and press the LOCK button during this time.4. Release in sequence the LOCK and UNLOCK buttons within 10 seconds of pressing the LOCK button in step3. (Perform the following procedure within 30 seconds.)5. With the second valid F.A.S.T.-key, press the UNLOCK button for 4 to 10 seconds and press the LOCK button during this time.6. Release in sequence the LOCK and UNLOCK buttons within 10 seconds of pressing the LOCK button in step5. The immobilizer display on the information screen in the multi-information display will blink. (Perform the following step within 20 seconds.)7. Touch the bottom back portion of the new F.A.S.T.-key to the engine switch.When registration of ID code is complete, the buzzer will sound three times and the immobilizer display will come on for 30 seconds. If an error occurs, F.A.S.T.-key programming will be terminated and the buzzer will sound for 3 secondsNOTE ? F.A.S.T.-key programming will be terminated if the operation mode is put in OFF before the immobilizer display starts blinking.8. If you wish to register another F.A.S.T.- key, repeat the process from step 1 after the operation mode is put in OFF..NOTE ? The immobilizer display will go off immediately if the operation mode is put in OFF. ? Perform the operation when the interrupt display screen is not showing. The interrupt display screen may prevent you from seeing the immobilizer display. ? It is not possible to register a F.A.S.T.-key if the immobilizer display goes off during the procedure.If you do not have 2 working keys you will need to find a locksmith in your area. Go to Locksmith Search
Use our Locksmith Search if you need professional help.